13_gecko_rubi
New member
Under hood or interior. Not both. Light bar would be under hood.any write ups on how connect say a light bar? Do you connect to all wires under hood and in footwell?
Sent via....
Under hood or interior. Not both. Light bar would be under hood.any write ups on how connect say a light bar? Do you connect to all wires under hood and in footwell?
You don't need to waste a switch on cb. There is an ignition hot 12v circuit inside as part of switch package. Wire cb to that. If u don't want it on just turn cb switch off.
Sent via....
Both the constant 12V and ignition 12V tied to the aux switch group are rated at 10A. For HAM you'd need to use one of the aux switches. They are rated at 40A for switch 1 and 2 and 15A for switch 3 and 4.Do you all know how much current each wire can handle? I was wondering if the hot inside can handle the 13 amps required by most ham radios.
Sent from my iPhone using JL Wrangler Jeep Forum mobile app
Any time!I like this guy. Thanks for all the insight, brother!
You don't need to waste a switch on cb. There is an ignition hot 12v circuit inside as part of switch package. Wire cb to that. If u don't want it on just turn cb switch off.
Sent via....
Both the constant 12V and ignition 12V tied to the aux switch group are rated at 10A. For HAM you'd need to use one of the aux switches. They are rated at 40A for switch 1 and 2 and 15A for switch 3 and 4.
Sent via....
You don't need to waste a switch on cb. There is an ignition hot 12v circuit inside as part of switch package. Wire cb to that. If u don't want it on just turn cb switch off.
Sent via....
Thanks, but I thought if you used any of the wiring that comes with the switch you are limited to only 4 connections one per switch. Am I wrong? if so that gives me one extra for rock lights.
As part of package there are 4 wires under hood (one for each switch) and 6 wires in interior (one for each switch PLUS a constant 12V hot and an ignition 12V hot).Thanks, but I thought if you used any of the wiring that comes with the switch you are limited to only 4 connections one per switch. Am I wrong? if so that gives me one extra for rock lights.
As part of package there are 4 wires under hood (one for each switch) and 6 wires in interior (one for each switch PLUS a constant 12V hot and an ignition 12V hot).
The extra two were put in interior specifically for things like CBs that you want an easy way to power but don't want to use one of the 4 switches for since the device has its own power switch.
Sent via....
Both the constant 12V and ignition 12V tied to the aux switch group are rated at 10A. For HAM you'd need to use one of the aux switches. They are rated at 40A for switch 1 and 2 and 15A for switch 3 and 4.
Sent via....
As part of package there are 4 wires under hood (one for each switch) and 6 wires in interior (one for each switch PLUS a constant 12V hot and an ignition 12V hot).
The extra two were put in interior specifically for things like CBs that you want an easy way to power but don't want to use one of the 4 switches for since the device has its own power switch.
Sent via....
It is a small cubby, you can order the switch kit from Mopar. I am out of state otherwise I would post a picture of mine. It is about the size of a business card depth and width wise. Maybe and inch tall.
Sent from my iPhone using JL Wrangler Jeep Forum mobile app
I noticed when you order the auxiliary switches they come with a 250 amp alternator and a 700 amp battery (is this a big plus?). Could you jump start the 700 amp battery if it went dead from a regular car battery or from a AAA jump start?
As part of package there are 4 wires under hood (one for each switch) and 6 wires in interior (one for each switch PLUS a constant 12V hot and an ignition 12V hot).
The extra two were put in interior specifically for things like CBs that you want an easy way to power but don't want to use one of the 4 switches for since the device has its own power switch.
Sent via....
Do you have a picture? Sorry I don't know what you meanDo you know what the orange wire you disconnect from the terminal and reconnect to the provided 2 way connector is for? I damaged the pin terminal and want to see if I could find a crimping tool and pin to replace it.
Thank yiu