REVERE THE STEER - 72.5" Dynatrac XD60 / PRO 1550 Front Axle

wayoflife

Administrator
Staff member
20170318131717-4a2ccaec.jpg


Just because everyone and their mother runs big offset wheels with 4" of back spacing or less, doesn't mean it's necessarily a good idea. While pushing the center line of your wheels further out will help you to run bigger tires and without rubbing issues, you do it at the expense of increasing your scrub radius and at the cost of putting more stress on your ball joints, wheel bearings and even tie-rod. Of course, for most in the industry, that's just the way things have always been done, but for Dynatrac, it's a problem they wanted to solve. As luck would have it, Cindy and I would get a chance to help them do just that and with the assistance of Rubicat. Sure, this was done on a 2012 Jeep JK Wrangler but from what we've been able to see of the JL so far, I don't think it'd be a stretch to assume that this axle may have been made with the JL in mind. :cool:

Bigger & Better
In addition to it's superior strength and significant weight savings, the Dynatrac PRO 1550 steering knuckle was specifically designed so that the steering axis inclination (the imaginary line you can draw through the axis of your ball joints) would meet at a point that's a lot closer to the center line of your wheel. By doing this, your wheels will pivot more instead of scrubbing as you make a turn and that alone helps to provide for much better steering and reduced stress on your tie-rod. In fact, the more back spacing you can run on a wheel (5.5" is optimal), the better everything will work especially with a set of 40" tires.
20170318132017-444ea591.jpg


Just to give you an idea of how much bigger a Dynatrac PRO 1550 is than a factory steering knuckle, here's a side by side shot of of the two. If you can believe it, the difference between the two is only about 1.5 lbs. and this in spite of the PRO 1550's massive size.
20170318132002-aaf66b35.jpg


Now, this is a side by side shot of standard PRO 60 steering knuckle on the left and a PRO 1550 on the right. As you can see, the opening is considerably wider on the PRO 1550 and this is to allow for a much bigger shaft. Also, because the PRO 1550 is made out of military grade aluminum instead of nodular iron like the PRO 60, it weighs about 8 lbs. less!
20170318132011-f98cf2aa.jpg


While the PRO 1550 steering knuckles alone will help improve your steering and a set of wheels with 5.5" of back spacing would make it that much better, Dynatrac understood that there are a lot of folks running coil over systems like the EVO DTD, Cindy and I included, and that this setup would prove to be a problem. To help address it, they decided to create a new version of their awesome XD60 that is wider... a LOT wider! For reference, a factory axle measures 65.5" wide and it can be difficult to run big wide tires or a coil over kit like the EVO DTD without running wheels with very little back spacing and in some cases, wheels spacers on top of them. A standard full width axle like a Dynatrac ProRock 60, XD60 or ProRock 80 will have a width of 68.5" and while the extra 3" will make it possible to run wheels with more backspacing, you'd still end up rubbing the bypass shocks on a EVO DTD setup with anything more than 3.5". This new version of the XD60 comes in a huge 72.5" width - that's a whole 4" wider than a standard full width axle and that will allow you to run a wheel with a whopping 5.5" of backspacing and without any rubbing!
20170318131946-6c34afac.jpg


If you're gonna buy a Dynatrac axle, it's always best to have one that's not only built by them but assembled by one of their technicians as well.
20170318131836-01185a20.jpg


Gotta love the XD60 differential cover in that it not only comes with a cool o-ring but it also comes with significantly bigger bolts that get torqued on and is used to help strengthen the entire housing.
20170318131847-1b3709f5.jpg


Final installation of our new 72.5" XD60 on Rubicat.
20170318132113-6451630d.jpg


Because there really hasn't been a means to accommodate high end bead lock wheels with a greater amount of backspacing, there hasn't been a need to make them and because of it, there aren't too many options to choose from. Fortunately for us, Trail Ready does and with 5.5" of backspacing - exactly what we needed and the best part is, they're made in the U.S.A.!
20170318115027-8a9192f6-me.jpg


Here's a shot that shows just how well the PRO 1550 and everything installed on it is tucked well inside the Trail Ready wheel.
20170318132050-b57575eb.jpg


A few minor modifications had to be made to the bypass shock mounts to make everything work but I doubt most could even see it.
20170318132049-19ea8eee-me.jpg


While we may have been able to run wheel spacers to help make up the difference in the rear, we decided to recycle our old ProRock 60 and have it rebuilt to a matching width.
20170318132038-4ea38187.jpg


Rubicat back on her feet again.
20170318114937-bc44e577.jpg


Look at all that clearance! Oh, and yes, a skid plate for the ram will be installed. It was left off for this photo shoot as adjustments were still being made to everything.
20170318114934-c1c20edb-me.jpg


Close up shot of the passenger side PRO 1550 steering knuckle.
20170318131944-ab0df257.jpg


Shot of the driver side.
20170318131942-53d2f43b.jpg


Time to do some fork lift flex testing to check for any rubbing or clearance issues.
20170318115019-1f8e8e78-me.jpg


20170318115031-fb493656-me.jpg


Just as it was designed, the drag link just misses the frame rail even at a full bump.
20170318114942-e05c02e4.jpg
 

wayoflife

Administrator
Staff member
For comparison, here are a few shots of Rubicat with her new 72.5" XD60 axle standing next to Dynatrac's JK which is running a standard 68.5" axle. Both axles have the PRO 1550 steering knuckles installed, both JK's are running Trail Ready bead lock wheels with 5.5" of back spacing and with 13.50" wide tires.
20170318125242-419ce750.jpg


Although the extra 4" of width isn't necessary for a standard coil and shock setup or even on a bolt on coil over system, Cindy and I would still run the 72.5" XD60 Cindy even if we weren't running an EVO DTD if only because it offers a nice, wide, lower center of gravity stance and without having to run wheels with very little back spacing. That being said, if you like a factory look, prefer to have your fenders cover your tires or need to because of state laws, going with a standard 68.5" width will get the same job done so long as you aren't running a coil over kit like the EVO DTD. Obviously, Rubicat is running trimmed factory fenders so her tires are sticking out quite a bit past the flares but as you can see on the Dynatrac JK, it's tires are tucked nicely under the Mopar hightop fenders.
20170318125251-f932c3ba.jpg


An added benefit of the PRO 1550 knuckles pushed far into a set of Trail Ready bead lock wheels with 5.5" of back spacing is the amount of clearance you gain under your axle.
20170318125327-7ab33e74.jpg


Of course, this is to say nothing about the protection your lower ball joints will have from the rocks as well.
20170318125337-3c7d71a5.jpg


20170318125306-e75c1ce0.jpg


As you can see here, the new XD60 front axle also comes with a built in ram assist mount and while ours doesn't have one installed yet, it can be outfitted with an EVO skid plate.
20170318125304-4f6f962f.jpg


We absolutely LOVE the new XD60 differential cover with its significantly larger 7/16x14 grade 9 bolts that can be tightened up to 85 ft lbs. of torque to and are completely recessed in the cover.
20170318125341-38eb1d46.jpg


For comparison, here's a shot of the Dynatrac JK with it's standard 68.5" XD60, running PRO 1550 knuckles and Trail Ready bead lock wheels with 5.5" of back spacing. You can really see the 4" narrower stance here.
20170318125345-7db227e2.jpg


In this shot, you can see the optional EVO skid installed to help protect the PSC ram.
20170318125354-624f6fe3.jpg


Being that the Dynatrac JK is running a standard coil and shock setup, it can run a standard 68.5" wide XD60 and still have all the same benefits provided by the PRO 1550 knuckles and while running a 5.5" back spaced wheel.
20170318125317-54c98432.jpg


Here are a few more all around shots of both Rubicat and the Dynatrac JK.
20170318125424-e9527a8d.jpg


20170318125419-ffe02781.jpg


20170318125416-11f92ce0.jpg


20170318125410-65c02f72.jpg


20170318125407-62e2752c.jpg
 

wayoflife

Administrator
Staff member
Here are a few all around shots that we took of Rubicat soon after bringing her back home to Camp WAYALIFE.
20170318131717-4a2ccaec.jpg


20170318131711-311992bd.jpg


20170318131722-004a67fe.jpg


Really liking her new Trail Ready bead lock wheels.
20170318131726-7b05754b.jpg


20170318131749-c5a04cc2.jpg


20170318131805-49df504c.jpg


20170318131756-c614b6ec.jpg


20170318131759-0466c14a.jpg


20170318131803-e2f3bfc6.jpg


A couple of shots of her updated ProRock 60 rear axle.
20170318131817-0f688481.jpg


20170318131828-7786d0a2.jpg


A shot of the front suspension. You can see how the bypass shock had to be changed to make this work.
20170318131916-9a9d8322.jpg


And finally, one more shot from the driver side.
20170318131858-1a0eb5de.jpg
 

wayoflife

Administrator
Staff member
So, here's an interesting comparison that'll help put some perspective on things. On the left, you have Rubicat with her new 72.5" XD60 front axle with PRO 1550 steering knuckles and running Trail Ready bead lock wheels that have 5.5" of back spacing. On the right, you have Moby running a standard 68.5" ProRock 60 front axle with Pro 60 steering knuckles and running ATX Chamber Pro II bead lock wheels that have 4" of back spacing. While Moby's tires are 40" tall, they're still only 13.50" wide just like Rubicat's tires and in spite of the 4" axle width difference, both Jeeps measure 85" wide from the outside edge of tire to tire.
20170318130127-cf45990f.jpg


20170318130134-f4f9e875.jpg


Here's a better shot of just Rubicat's 72.5" XD60 with PRO 1550 steering knuckles.
20170318130157-73f278a5.jpg


And, this is a shot of Moby's 68.5" ProRock 60 with Pro 60 steering knuckles.
20170318130202-ec9a5de6.jpg


An even closer shot of Rubicat's axle.
20170318130207-279764e8.jpg


And now Moby's front axle.
20170318130212-ae5e1c35.jpg


Angled view of Rubicat's XD60.
20170318130313-598a9054.jpg


Angled view of Moby's ProRock 60.
20170318130344-3bc7e528.jpg


XD60 differential.
20170318130320-73dc4218.jpg


ProRock 60 differential.
20170318130341-c5963966.jpg


PRO 1550 steering knuckle tucked far into the Trail Ready bead lock wheel and with lower ball joint completely protected.
20170318130239-39302c78.jpg


Pro 60 steering knuckle sticking way out of the Chamber Pro II bead lock wheel and with the lower ball joint completely exposed.
20170318130406-c999e335.jpg


Shot of Rubicat's modified EVO DTD bypass shock with relocated adjustment tubes and frame mounted reservoir.
20170318130304-ff262cf0.jpg


Moby's standard EVO DTD bypass shock setup with adjustment tubes facing out and reservoir mounted on the side of it.
20170318130412-d994f33e.jpg


Here are a few parting shots of both Rubicat and Moby side by side.
20170318130150-2d251a87.jpg


20170318130148-ee98366e.jpg


20170318130146-763e23f6.jpg


IN A NUTSHELL

Why You'd want an XD60
• Dynatrac signature profiled center section that offers maximum clearance.
• 10.1" ring gear which is 16% stronger than a 9.75" Dana 60 gear.
• New center section with increased rigidity.
• Significantly larger carrier and pinion bearings for greater strength.
• Lighter than a ProRock 60.
• Proprietary internal Dual Sump High Volume (DSHV) lubrication system that provides optimal oiling.
• Cast-in features for optimal air and electric locker connections.
• 3-3/4" OD axle tubes with 1/4" or 5/16" wall thickness.
• Differential covers designed to provide additional strength to the center section.
• Differential cover O-ring that replaces traditional gasket.
• Deeply recessed differential cover bolts holes for maximum protection.
• Largest in the industry 7/16" fasteners.
• Massive 1550 axle shafts.
• 68.5" width allows for wheels with 5.5" of back spacing

Why You'd want PRO 1550 Steering Knuckles
• Made of military grade aluminum.
• Significantly strong than stock and only 1.5 lbs. heavier.
• Stronger than a Pro 60 and 8 lbs. lighter.
• Ball joints are pressed into knuckle instead of end forging.
• Bigger bore allows for use of massive 1550 joints or Series 30 CV joints.
• New bigger upper ball joint.
• Taller knuckle pushes ball joints out providing more leverage on tires.
• Improved steering axis inclination reducing scrub radius.
• Significant improvement in steering.

Why You'd want Wheels with 5.5" of Back Spacing
• Brings center line of wheel in and when used with a PRO 1550 knuckle, dramatically reduces scrub radius.
• Reduces stress on ball joints and wheel bearings.
• Protects knuckles, brakes and lower ball joints.

Why You'd want a 72.5" Wide Axle
• To run wheels with 5.5" of back spacing and still maintain a wide stance.
• To clear EVO DTD coil over system components at a full turn and stuff.

After 8+ years and well over 100,000 miles of punishing our Dynatrac ProRock 60 front axle on Moby, I'd be the first to say that I truly wondered whether or not an improvement to it was really needed. That being said, I'm glad to know that Dynatrac is the kind of company that is never satisfied with a "good thing" when "better" can always be had.

Without question, the XD60 front axle is simply amazing in its design, superior strength and lighter weight in spite of some of its larger features. Coupled with PRO 1550 steering knuckles, a set of wheels with 5.5" of back spacing and wider 72.5" axle width if necessary, the XD60 will steer with ease (even with your lockers on) and have a turning radius similar to a factory front axle. For those of you who know, this is a HUGE improvement over the ProRock 60 which can at times feel more like driving a full size truck than a nimble Jeep. Of course, the ability to bring the center line of your wheels inward means that you'll put a less wear and tear on your ball joints and wheel bearings and being that your tires will no longer pull inward when taking on tough climbs, your tie-rod will see a lot less stress as well.

I literally could go on and on but I'll stop here and be more than happy to answer any questions you might have. :cool:
 

Top